ZirkonZahn Milling Burs for Zirconia

$49.90 $69.90

CVD diamond zirconia burs compatible with Zirkonzahn mills

6 mm-shank Eagle burs compatible with Zirkonzahn milling units that use a 6 mm collet, CVD diamond-coated for zirconia. Sold one bur at a time in 0.5, 1.0 and 2.0 mm; check your machine's collet size before you order.

Read more >

Related products

Zirkonzahn burs for zirconia: CVD diamond, 6 mm shank

These Eagle CVD diamond-coated zirconia burs have a 6 mm shank and are compatible with Zirkonzahn milling units that use a 6 mm shank / 6 mm collet. Each bur is sold individually in 0.5, 1.0 or 2.0 mm, so you replace only the tool position that is worn.

Specifications

Compatible with Zirkonzahn milling units with a 6 mm collet
Shank diameter 6 mm
Coating CVD diamond
Materials Zirconia and other abrasive ceramics
Sizes 0.5 mm, 1.0 mm, 2.0 mm
Quantity 1 bur per unit

What each size is for

Size Typical job Lab note
2.0 mm Roughing and bulk removal Runs on almost every job
1.0 mm Finishing crown and bridge surfaces Shapes contours and inner surfaces
0.5 mm Fissures, margins and tight anatomy The most delicate size, so keep a spare

How to read the sizes

The size on each option is the cutting diameter; the shank is 6 mm on all three. Your milling software assigns each diameter to a tool position, and the strategy expects that exact size there. Check which position has reached its tool life before you order, and add each size to your cart separately if you need more than one.

Why CVD diamond for zirconia

CVD (chemical vapor deposition) builds a crystalline diamond layer on the bur. Pre-sintered zirconia is highly abrasive, and a CVD diamond layer is designed to hold its cutting edge in this material, from roughing to finishing.

  • CVD diamond: crystalline diamond for abrasive materials such as zirconia. This is the coating on these burs.
  • DLC (diamond-like carbon): a thinner amorphous carbon coating that reduces friction but is not true diamond.
  • Uncoated carbide: the sharpest edge, best for PMMA, wax and PEEK, but it wears quickly in zirconia.

Keep these burs for zirconia only and use separate uncoated burs for soft materials, so each tool keeps the right edge for its job.

Installing a replacement bur

Follow your machine manual and milling software for the exact steps. In general:

  1. Finish or pause the job and make sure the spindle has stopped.
  2. Remove the worn bur and note its diameter.
  3. Clean zirconia dust from the tool holder and collet area.
  4. Insert the new bur straight, without forcing it at an angle, to the depth your machine requires.
  5. Register the bur in your software's tool management and reset its usage counter.

When to replace zirconia milling burs

There is no fixed number of units per bur. Bur life depends on the zirconia type, blank height, milling strategy and how much fine detail each job has. Replace a bur when you see:

  • Rougher surfaces or tool marks on milled crowns and bridges
  • Chipped or uneven margins, especially in thin areas
  • Longer milling times than your software estimates
  • Poorer fit of copings and frameworks after sintering
  • A dull tip, worn coating or chipped cutting edge
  • A tool-life warning from your machine

Tips for longer bur life and better surfaces

  • Use the milling strategy your software recommends for your zirconia blank.
  • Keep collets, tool holders and the milling chamber free of zirconia dust.
  • Insert burs straight; forcing a bur in at an angle can damage the tip.
  • Store spare burs in their packaging, not loose where they can knock together.
  • Do not reuse a bur that was dropped or has a chipped edge.

Troubleshooting zirconia milling

  • Broken bur: a worn tool kept in use, a bur not seated straight, dust in the collet or a strategy that does not suit the blank.
  • Chipped margins: a worn or chipped 0.5 mm bur.
  • Rough surfaces or visible steps: a dull bur or the wrong diameter in a tool position.
  • Poor fit after sintering: worn burs on inner surfaces; also check calibration and the blank's shrinkage settings.

Compatible Eagle burs, not original tools

These are Eagle burs compatible with Zirkonzahn milling units, not original Zirkonzahn tools. They have a 6 mm shank, so check your machine's collet size before you order, then register each one like any replacement bur. For zirconia burs for other mills, see our zirconia milling burs, or browse all dental CAD/CAM milling burs.

Ready to Subscribe?
Eagle Dental Burs newsletter